Wednesday, 5 October 2011

spark plugs

I cant for the life of me find any reference to the specification of the correct spark plug for my scooter.  Various owner manuals can tell me that my ignition is "Magneto, fixed spark advance" and that my points should be ".016" - .02" " etc but no mention of what sort of replacement spark plug.
My Manurhin came with a spark plug in it, but as the bike in general had been so abused, I am being cautious as to wether this is a spark plug as specified.

The plug in my bike is an AC 44-5V

I came across The Green Spark Plug Company on the internet and thought I would do a little research into sparkplugs.  Crikey! I hadn't realised how complex it all was, and so I gave them a call to see if they could enlighten me.
The very helpful chap at GSPC informed me that an AC 44-5V was very likely the correct plug for my scooter (and very common for scooters in general).  They were out of stock of those but the very reasonable J8C would be a suitable alternative (see the photo alongside for a comparison of these plugs - seems like a 'copper core' electrode is the only difference - and these are supposed to be better for high temperatures..... not that i imagine my Manurhin getting that much wear)
I pressed him further for suggestions on plug caps, and once again he informed me that my application was pretty common and a standard non-suppressed LZFH would do the job handsomely.
Feeling flush I took the plunge and ordered a meter of 7mm PVC HT lead too.

Total cost including postage; £7.82

Tuesday, 4 October 2011

Starter rope

The puller rope on my starter assembly is damaged.  It was damaged when I bought the starter assembly off eBay, and until now it hasn't been a problem for me to think about, but as the engine slowly comes back together, I need to get it working again.
Stripping the spring return assembly is all pretty straight forward, but it clearly is something that hadn't been done for a while - it was full of a thick cake of mud, dirt and oil, severely restricting the free movement of the engagement plates.

I had originally intended to simply replace the original and damaged wire pull rope with a modern nylon rope designed for lawn mower engines, however it turns out that a lawn mower pull rope is too thick to fit comfortably around the assembly, and so I had to go in search of a replacement flexible wire rope.

There are many specifications for wire rope, and not all wire rope is suitable for such regular wrapping and unwrapping around a tight diameter like the Manurhin starter device.  And so it was with little confidence that I went to see a local wire rope supplier.  But how wrong could I be?

Rope Services Direct Ltd were fantastic.  Mike was not only interested in my problem, but had exactly the wire rope i needed (2.5mm dia. Multi-strand, stainless steel) and hundreds of other types of wire besides.  He also threw in a handful of appropriate end terminals for me - all for the price of a beer!
Incidentally; Rope Services Direct Ltd can also create bowden cables to any design and end fitting, so they may well be very useful a little further down the line when it comes to break and throttle cables too

Monday, 3 October 2011

Registering my scooter

I've had a little niggle in the back of my mind for a while now, and although it is still a long way off, I am slightly concerned about the process of registering my scooter - especially as I have no previous documentation or proof of its originality [though I hope in some way this blog will be able to illustrate its authenticity]
As I was eating my breakfast the other morning I was reading the latest edition of Old Bike Mart (I thoroughly recommend everyone subscribing - its better than.... well anything that you think is really good)
I read with interest about a 1928 Indian scout project that had just been "issued a dating certificate" so that the owner could apply for a period registration number.  This piqued my interest and so I dropped the writer an email to ask more about this process.

Mike Worthing emailed me back;
"My dating certs are accepted by DVLA. I provide the cert, all the DVLA paperwork filled in for you to sign and retain, and a step by step drill to follow to obtain an age related number. The fee for this services is thirty pounds (payable to me please) and my address is in Old Bike Mart"


So this might be a useful contact for the (lets hope not too distant) future.

Fitting the crankshaft

I remember quite clearly my anxiousness when it finally came round to fitting the crankshaft back into my Vespa PX 200 engine.  And despite that previous experience going pretty smoothly, I didn't feel any less anxious this time round either.
I use the tried and trusted method of heating one part of the assembly to expand it, and freezing the other part of the assembly to contract it - then if you are quick enough to maintain the temperature differences, the two closely fitting parts slide together relatively easily - the key phrase here being "if you are quick enough" - it is all a bit of a 5 minute rush and panic.

I think much of the success in fitting bearings and crankshafts is in the preparation - having pullers and blocks ready to hand to help the quick process of fitting fully home.  I made up a whole bunch of plates to spread loads, and tubes to pull down on and laid them all out neatly ready for action.
So with the two bearings just out of the freezer, and a blow-torch on the engine casings (hot enough so you cant touch, but not so hot that things are glowing) the bearings went home beautifully.
For those who are interested - I made great effort to ensure I didn't forget to put back the "compensating washer" before dropping the main bearing in.  I am not sure how I should have determined if this washer was still doing the right amount of 'compensating' (or indeed what it is compensating for) but I decided to simply put back the washer that I took out when I unassembled the engine - it was 0.5mm thick.

Next step - fitting the crankshaft into the new bearings - this of course requires the closing of the two halves of the engine case, so fitting the new gasket all takes a little more preparation and time

The crankshaft only needed a couple of hours in the freezer to chill.  With the larger engine-case half suitably warmed by blow-torch, and the bearing heavily lubed up with grease it was a relatively quick and easy fitting, though it did need my prepared puller to draw it home properly.
To fit the other side bearing, the engine cases have to be closed, so while I was Red-Hermatiting the gasket the crankshaft was slowly warming back to ambient temperature which would mean that I wasnt going to have the same expansion/contraction advantage as I did on the first bearing.  However, I still heated up the smaller engine-case side and bearing and sure enough, it went home without too much fuss or bother.

I have to say, it was a great relief as I tightened down the engine case bolts to feel the crankshaft spinning silently and freely.

Replacement bearings. Theory vs Reality

Now pay attention, because this is complicated (or boring - depending on your interest in these sorts of things)
I am blessed to have a complete spare parts manual (in English) for my Manurhin - and I am indebted my friends in the Manurhin Scooter Interest Group for these invaluable documents, and so armed with these documents I asked PJ Motorcycle Engineers to supply me with the listed bearings and seals.  I was delighted when they said they recognised the part number references, and sure enough they could supply exactly as stated in the spare parts inventory

However, when I got back to my garage and laid out the new bearings to compare with the old ones, something was wrong.  I had the correct new bearings (as indicated by the spares list) but they didn't all match with the actual bearings that I had removed from the engine.  To be clear - the inconsistency is in the crankshaft bearing - flywheel side.
In the exploded diagram to the right, you can see bearings marked as parts No.16 and No.19.
Part No.16 is identified as a 6303 bearing - and indeed the part I removed was a 6303


But my confusion starts with part No.19.
First of all the parts-list shows 2 alternatives for this bearing - depending on the type of coupling your crankshaft has.  This becomes even more complicated as I try to identify the type of coupling - Ive highlighted in blue on the above parts list, the two alternative couplings - and I have no idea what this means (any insight on this would be gratefully received)  All I can confirm is that my own crankshaft has a tri-lobe drive (this could be what the list calls 'polygone') on a 15mm dia shaft - which might lead us to identify with Part No.21 - the 15mm dia oil seal (as opposed to Part No.21A - the 17mm dia oil seal)

I did warn that this is all very complex and boring!
So according to the parts list I should expect to have either a 6303 bearing or a 6203 bearing.  Curiously, the bearing I removed is neither of these

Regardless of what the parts list says,  the actual bearing that I removed from my engine is a 6202. which as can be seen in the photo alongside is very much smaller in diameter than a 6303 or 6203.
(note the 3rd bearing down - the largest diameter one - is the bearing type - 6303 - required for the other side of the crankshaft)

I spent ages scratching my head, checking, cross-checking and measuring and in the end decided that all I could do was simply replace what came out of the engine in spite of what the parts list said.
Fortunately, as I had decided not to replace the transmission bearings (but had bought them anyway), I had a new 6202 bearing (as shown at the top of this photo) so I am all set to get that crankshaft back where it belongs.
I feel slightly anxious.

Sunday, 2 October 2011

More reference numbers

Oooh I've found some more engine reference numbers.  They are very subtle and I have only just noticed them.  They appear to be hand etched with a vibrating engraving tool.  I have no idea of their significance (and in fact I'm not sure if I can read them completely) but I suspect they might be something to do with matching the engine case halves during manufacture.
The numbers appear to be similar on both halves of the case and can be found on the bottom side of the cylinder barrel port.

Crankshaft balancing

Partly prompted by the fact that I couldn't remove the small bearing from the crankshaft (see earlier post) I decided a couple of weeks ago to get the crankshaft over to a specialist to get the bearing removed and to have it all balanced.  When I rebuilt my Vespa engine, I didn't bother to have the crankshaft checked or balanced, and I am rather regretting that now; the poor old thing rattles and vibrates like buggery - in fact after an hour of so in the saddle, I can get 'white finger' numbness! [as an aside, I think i have resolved to get the Vespa engine out again in the winter to get this sorted]

I took the crankshaft over to (the relatively local) PJ Motorcycle Engineers.  It was comforting to walk into their shop and see lots of performance engine bits and not a helmet, headlamp or bit of bling-trim in sight.  They looked like proper motorcycle engineers and appeared interested in my peculiar engine, and although it took them nearly 2 weeks they balanced my crankshaft and supplied 6 new bearings all for the very reasonable price of £45.  Apparently my crankshaft was 3 thou out of true (I have no idea how big a deal this is, but I see on their website that a single thou can make all the difference)  My understanding is that they were happy with the big-end bearing (though I couldn't work out if they had actually taken it apart)

Since getting the crankshaft and bearings back, I have been looking at the transmission shafts and bearings, and I've decided that I am not going to change those bearings this time round (they look and feel ok, and I am worried about how to extract the bearings in the blind holes without removing the end caps and causing all sorts of problems in replacing them)