Saturday, 1 October 2011

Exhaust and silencer

And while I was in the mood for gently persuading seized things to come apart (see previous post about piston rings), I thought I'd have a go at the exhaust and silencer assembly - As I get closer to getting my engine together I am thinking about trying to start it on the bench, and so I will need the exhaust pipe soon.

I understand that Manurhin exhausts are quite rare to find, so I count myself lucky that although most essential parts seem to be missing from my scooter, I do at least have an exhaust system.  It seems to be all there, but it it rattles terribly with what i guessed to be rust.  The Manurhin parts catalogue shows that there is a removable/serviceable muffler assembly inside the outer casing and this is accessed by removing a nut and end-cap.  It was clear that these parts were well rusted together, so once again I've been soaking the thread and joint in WD40 for a week or two.

Today I applied some heat with a blow-torch, and amazingly the nut released (I was preparing to sheer it off and weld a new thread in).  A little more heat, some tapping the joint with a hammer, and sure enough the cap came free.

I was delighted to find that despite a little pile of rust, the muffler is in remarkable shape.

I think a quick wire brush and a spray of exhaust paint, and this bit at least should be good-to-go

Piston rings

A few months ago I was witness (party to?) a frustrating moment as a friend attempted to free the rings from the piston of an ancient scooter he was rebuilding that hadn't run for years.  The rings were well stuck (though not welded in, so certainly salvageable).  He'd been soaking them in penetrating oil but was now very keen to get them out and so with the help of some heat from a blow-torch we set about getting them out.  Alas, we were too hasty, and sure enough we snapped one ring.  Under normal circumstances this might have simply cost a couple of days and a couple of quid, but as the engine was rare, it took him a great deal of effort to source a suitable replacement.

If any good was to come out of that experience, it was that I learned a valuable lesson; or rather it reinforced a mantra "patience is a virtue".
As a consequence, I've been soaking my Manurhin piston and seized rings for many weeks now - ive been in no rush.  This morning however, I decided to get proactive.  While the wife was still asleep in bed, I popped the piston on the kitchen stove and set it to boil.  Every now and then, I whipped it out, gave the rings a little tap around with the wooden handle of a screwdriver, squirted some WD40 on, let it cool..... and then repeated the process.
Hey presto, the rings eventually let go of the piston and sprung out like new.
A little patience and some gentle persistence, and I've saved myself a lot of heartache

Sunday, 25 September 2011

Beltomatic assemblies

With the engine all in pieces and waiting for parts to arrive, I decided to occupy myself with overhauling the Beltomatic (I love that word) drive assemblies;  after-all, its all very well making the engine run sweetly, but if the power isn't going to transmit reliably then the whole thing is a waste of time.

This is an ingenious piece of design and engineering that requires springs and counterweights and bearings and sliding bits.  I only hope it performs as well as it looks like it should.

There was nothing particularly complicated about stripping it down.  There is a retaining circlip on the primary assembly that wasn't compatible with my circlip pliers, but nothing that a couple of screwdrivers and a little patience couldn't handle.  I was surprised to find that the needle rollers on the primary drive are held in an alloy cage, and even more surprised to see that the cage was still in good condition.  There were a number of "compensating washers" taking up the lateral movement in the assembly - I have no idea what the factory setting should be for this slack or if my compensating washers are still appropriate, and so I shall reassemble as found and see how she fairs.

After a complete strip and jolly good clean down (its amazing how much the accumulated crud can restrict the ease of flyweight movement) I spray painted the drive plates with Smooth Black Hammerite.
Definitely a job worth doing as the assemblies feel so much more free now, and I am confident that all the parts that will require lubrication can now get it.

Engine Gasket Set

Now committed to a full engine rebuild, I went in search of a gasket set.  And sure enough I found someone out there who makes gasket sets for old motorbikes.  Of course there is!  I often wonder what it might have been like to do a project like with without the use of the internet (and then my mind usually wanders to the next question..... what will it be like to do a project like this in say 25 years time, when [internet] technology might have evolved into something we cannot even begin to imagine!)


I noticed on the Klamotte website that they sold gasket set for DKW Hobby engines but there was no mention of Manurhin.  As I wasn't sure if there might be some subtle differences,  I emailed them to ask if the Hobby Gaskets would suit my Manurhin.
Their response? "Hello, I´m sorry, but I don`t know this engine"
Really!??


Fortunately, fellow Manurhin owner, Roy, had already told me that this gasket set was suitable so I went ahead and ordered anyway.


So, for 21 Euros plus 4 Euros shipping, I now have a engine gasket set.  Just got to get those bearing changed now and it can all go back together



Sunday, 11 September 2011

Engine casings

Now most of the bearings are out of the engine casings, I can give the casings a jolly good clean and inspection.
Generally the casings appear to be in good condition, but I was a little worried to see signs of 'chattering' on the insides of the crank casing.

I wonder what might have caused this?
Will new bearings solve this? and has the engine been damaged now because of this wear?
Do I have to get them machined smooth again?

Plenty of things for me to be thinking on over the next couple of weeks while I am away from the garage.

Bearing extraction

So I managed to get the crankshaft bearings out of the engine casings with a little bit of jigging and extracting, and I think Ive found a chap who can supply new bearings to suit (I will get round to seeing him over the next couple of weeks).
The only bearing left now to extract is the one that came out of the casing still firmly attached to the crankshaft, and I am buggered if I can get it off.  The trouble is that it is so closely up against the counterweights that I cant get an extractor or a purchase behind the bearing.  I've tried some heat and clamping in a vise, but no joy (actually I'm not convinced that heat is going to help because I cant heat it without heating the shaft too, which seems to defeat the point)

So what to do?
Well, I decided in the end to leave it for a while, let some penetrating oil do its job and spend some time incubating on the problem while I overhauled the clutch assemblies.
All suggestions on how to remove this bearing will be gratefully received :-)

Crankshaft machined

A while ago while out in our local curry house, I bumped into an old friend.  He owns a successful engineering company, and I was quick to ask him if motorcycle engines were something he ever had the pleasure of handling.  His answer was simple - "NO - too much hassle" (and to be fair to him, if your business is tier 1 engineering supplier to the auto manufacturing trade, nobbing about with private one-off jobs probably is more hassle than its worth) - "But, if you want to drop it round, I'll have a look at it for you.... as a friend".  And so I did.

It turns out that the sheered pin in the crankshaft was hardened, and so the only way out was to spark erode it out.  The Manurhin workshop manual calls this little pin "a magnetic cotter pin" - im not sure why 'magnetic' but my engineer friend and I decided that a new pin made from a piece of silver-steel would be tough enough to do the alignment job and yet sacrificial should anything fail (I'm relying on the tapered shaft to do all the securing of the flywheel)
Note only one hole was spark-eroded.  It looks oval at the top, but its a good true 2mm dia hole deeper down
Normally when updating this blog I would put a link in to the supplier or source of information, but in this instance, I'm not sure if Richard of RPS engineering in Birmingham would be overly grateful to receive a little queue of scooter tinkerers asking for fiddly-piddly machining jobs.  Its not really what his CNC machines are cut out for.